Saturday, 16 January 2016

The Birth of an Airship

I know I have been AWOL lately, but this is a large reason for me not being at my desk.  This and a 3.8m (12ft) x 1.8m (6ft) art installation for Truth Coffee.

In March of 2015 I was commissioned to do an art installation for the "best coffee shop in the world" for 2015... I kid you not... Google that statement and it will come up! 

 This is a photo heavy post...
What started out as a pile of randomness finished up as the airship seen above!!!!
To build the fuselage I began with 7 hula hoops, one bigger than all the rest for the center hoop. 
 Then I cable tied the 3m long strips of electrical conduiting to the hula hoops on pre-measured and marked points.  along the way I decided only 5 hula hoops were needed.
I then used the most complex tool of all to join the nose and tail together.... Wait for it.... Packaging tape!  
The nose cone is a vuvuzela (a relic from the 2010 soccer world cup held here in SA) and the boat propeller which I salvaged at car boot sale proved to be too heavy, so I manufactured one out of a mini hazard cone and foam core board.  When the glue dried I sprayed it copper and added texture paste so that I could pant it to look old and rusted.


While this was "aging" I covered the "highly engineered" (tongue in cheek) frame with fabric using gel medium which I painted brown when it was dry.



 I then went back to the hardware store for the I umpteenth time to get a floursescent tube light fitting, wiring and some "Mc Guyver" parts to suspend it inside the airship.  (By now the men had given up asking if they could help me while I wandered the isles of bolts, rivets and electrical parts - probably wondering what a girl with bright pink hair could be up to with her eclectic shopping sprees)


I found 24m of webbing to cover the joins in the fabric and 700 rivets were used to make it look pretty.
So that the light can be worked on in the future, I made access hatches on both ends of the airship sealed with Velcro.  You can see this below as well as a wet coat of gel medium which sealed the pores of the fabric making the ship glow instead of being able to see the light fitting through the fabric when the light was on.
I then glued some paper cogs onto her sides for added steampunk vibe and wrapped her nose and tale in fabric tape to give a bit more strength to the packaging tape.

I decided she needed some stabilizers and using the logo from the coffee shop, I devised some fins in 3 layers of foam core.  
This is the top of the fins where I marked the spot to glue the straws into which the carbon fiber rods will slide.  The underside has the design on it so you see it when you look up.
To make the gondola I made a structure out of foam core again... My favorite building material... and covered it in an engineered photo of the Truth Coffee building which I had printed locally.  As the public will be viewing this from below, I created the illusion of bricks underneath her and because the office will view her from above, I added corrugated cardboard painted silver to emulate a cast iron roof.  I then suspended this under her hull with some chain.
In the photo above, I was working out how to do the ends of the gondola.  I eventually cut the ends oval to emanate the ones on the Zeplin
I used texture paste through a stencil I made from Tim's brick die.
Above has the base coat of paint, below, I rubbed the Archival Coffee ink pad directly onto the raised areas.
Here you see her upside down on my desk as I worked...
The last things to go onto the fuselage was the nose cone and propeller which got glued on and the fins which had carbon fiber rods to slide onto which run right through the fuselage and into straws under tape...  Yet another "Mc Guyver job".  

Here she is in my car port where I built her over a period of 5 months


Tuesday, 22 December 2015

Tim Holtz December tag 2015

 I recently taught a technique tag class and had designed 4 of the 5 tags... I had hit a blank on the 5th one and no matter what I tried or put together, it did not seem right.  Then it was Tim to the rescue with his December tag inspiration on Tuesday the 1st, not a day too soon as my class was on the Friday, so I had 2 days to design my tag and kit up!
I did not have his punches, so decided to go back to his tags from 4 years ago when he last did a wreath... then I added the typewriter from another tag done that year and was finished!
Phew!
12 tags of 2015 - December | www.timholtz.com
This is Tim's tag and you can find his instructions here!

Tuesday, 15 December 2015

How To Make Distress Ink Towers

A few people have seen my 3 Distress Ink Towers on my desk and asked how I made them... Here goes:

I used foam core/board sheets to create them in two thicknesses.  Here in South Africa, we work in metric measurements and the one board is 5mm thick and the other 3mm.

When using Tim's ruller to try convert them to inches the 3mm = one tiny little square (1/8?) and the 5mm =1.5 tiny little squares... Does this help?  Don't know how to say such small measurements in inches as they are not common to me.  The bigger numbers I can do!

Moving right along...

The sides measure 3"x 18.4/8" (cut two from 5mm)
The back is 3.4/8" x 18.4/8" (cut one from 5mm)

The shelves are 3.3/8" x 2.4/8" each (cut 15 from 3mm)
(my measured dots are in the wrong place in this close up, but my score lines are correct...)

Take one of the sides and measure half an inch in from the side and draw a light pencil line from top to bottom.  This will be the front of the tower.  Starting at the bottom of this pencil line measure 9/8 and make a dot then at 1" and make a dot.  Do the same along the back edge of the side.  Repeat the other side piece.
Now turn them over and stick them together with painters tape or low tac washi tape.  Turn them over and score together.
Using a craft knife and metal ruler score down to the paper base, but not through it.
Then take a screw driver and scrape out the foam from the pencil line,  between the score lines to the back of the side. 
 Now you should have two matching sides.  I chose to not go right to the top and leave the last shelf out and make a deep area to store my re-inkers, as seen below
 I then run some Glossy accents into the hollows and place my shelves into them and weight them down with my distress inks.  When this is dry, I glue on the back and a piece to fill in the top shelf.
 When dry, I use Tim's tape to decorate the edges all round to hide my joins.
 Here are my 3 towers.
 This is the back.
 Here you can see the deep shelf to house my re-inkers at the top.

Please tell me if these measurements are up the spout or if my instructions are not clear...  This was hard to explain, thankfully I think my photos help...

Friday, 13 November 2015

Finnabair Over Emotional class

I know this post has been a long time coming...  Life got in the way! It is hard to believe that this photo was taken 2 weeks ago!

We booked this event way back in January.  Then we found that a total of 9 Capetonians were going up and so we got together as often as we could to craft as a group to get to know each other better and called ourselves the Finnaberries!  (We found more Capetonians when we got there... it was nearly a take over!)
Finally the day dawned and I took a road trip up to Jeffrey's Bay with a friend called Jo (seen above looking bright eyed and bushy tailed at 6am!) to join 5 other Finnaberries to do a class with Finnabair.

Two of the Finnaberries did the class before us on the Thursday and Friday... We managed to catch them for a photo when we arrived in JBay

The event was everything I had hoped for and more.

 We were spoiled with gifts on our tables from the Scrapbook Studio who hosted the event.  Here are the various things set out on my guest house bed below:



Here are the 3 Basson girls (not related, unless you consider that distress inks run in our veins...) all in the same room, brought together by Anna from Cape Town, Secunda and JBay.  It was a really special moment.
  This is Patricia Basson with her Finn style headband!  We have been online friends for a long time, so it was lovely to finally meet in person!
How awesome is this kit we got to build our canvas from?
Here Anna is showing us how to make the drips.
  What would an event be without some retail therapy?
  In my element!
 Off to make my drips on the canvas... looking a little sad as the day was coming to an end.
 The Finnaberries in the aprons I made for each of us and Anna
 I was put under the teacher's nose... I think that was to keep me good!
Here is my finished canvas
 Day two was taught by Cariena and Jowilna
Jowilna taught us lots of lovely tips and tricks and I even managed to stick to the page layout and finished a page as it should be... well, almost! 

Cariena had us playing with Zig markers to colour stuff.  Well I clearly had lots of fun in this class!

 This is the awesome team behind the event.  They work tirelessly to make sure that it all runs smoothly.  They are truly fabulous!
Thanks to Precilla and her camera, I actually exist in photos.... a rare occurrence and much appreciated!